Ķīna Double reģeneratīvā Krāsns Termiskā efektivitāte rūpnīcu un ražotāji | Yinuo

Double reģeneratīvā Krāsns Termiskā efektivitāte

Īss apraksts:

Introduction: the national standard energy-saving cycle type furnace, super energy-saving structure, with composite fiber insulation, super lightweight high strength beads vacuum energy saving brick, exclusive rights to produce the brick off 20 ° inclined put on silk silk, collision brick front against the workpiece, automatic sealing car and oven door, integration of rail, without foundation installation, can be used on a level surface.

Scope of application:Mainly used for high chromium, high manganese steel castings, gray cast iron, nodular cast iron, roll, steel ball, hammer head of crusher, wear-resistant lining plate quenching, annealing, aging and heat treatment of various mechanical parts.


Product Detail

Preces birkas

Structure:

The bottom of the regenerative trolley heating furnace is a movable trolley.Before heating, the trolley loads materials outside the furnace, the heating parts are put on the special pad iron, and then the trolley is pulled into the furnace by the traction mechanism for heating. After heating, the trolley is pulled out of the furnace by the traction mechanism for unloading, and then the heated workpiece is hoisted to the forging and pressing equipment for processing by the crane.

Introduction:

The national standard energy-saving cycle type furnace, super energy-saving structure, with composite fiber insulation, super lightweight high strength beads vacuum energy saving brick, exclusive rights to produce the brick off 20 ° inclined put on silk silk, collision brick front against the workpiece, automatic sealing car and oven door, integration of rail, without foundation installation, can be used on a level surface.

Scope of application:

Mainly used for high chromium, high manganese steel castings, gray cast iron, nodular cast iron, roll, steel ball, hammer head of crusher, wear-resistant lining plate quenching, annealing, aging and heat treatment of various mechanical parts.

中钢蓄热式锻造炉

Advantage:

1.Average gas consumption: 45-55m3/t.(natural gas)

2. Smoke extraction temperature ≤150℃

3. Furnace temperature uniformity ≤±10℃

4. The average life of imported components for directional valve is ≥ 200,000 times.

Function:

Regenerative combustion can improve the flame radiation intensity, enhance radiation heat transfer and increase furnace output.

蓄热 式 台 车 加热炉

Double reģeneratīvā apkures krāsns

Tehniskie rādītāji:

Apkures detaļu: lieli kalumi

Sildīšana temperatūra: 1250 ° C

Izplūdes gāzu temperatūra: 70 ° C

Gaisa uzsildīšana temperatūra: 1300 ° C

Degviela: dabasgāze

Degvielas siltumspēja: Qd = 8400 × 4.18kJ / m3

Original krāsns veida: izliekta velve

Iekraušanas un izkraušanas metodes: ratiņu

Original krāsns degļu: top dzīvoklis liesmas rakstītājs

Dūmu izvades režīms: sānu izplūdes

Vidējais degvielas patēriņš: <60m3 / h

Vidējā krāsns siltuma efektivitāte: ≮48.5%

 


  • Iepriekšējais:
  • Nākamais:

  • Uzrakstiet savu ziņu šeit un nosūtiet to mums

    Saistītie produkti

    • Trolley type heat treatment furnace

      Trolley type heat treatment furnace

      The gas heat treatment furnace is a national standard energy-saving periodic operating furnace with an energy-saving structure. The trolley adopts anti-impact sealing, the furnace door adopts an automatic spring-type compression mechanism, and the trolley and furnace door are automatically sealed, integrated and connected, and no foundation installation is required. It can be used on a level ground. Mainly used for high chromium, high manganese steel castings, ductile iron, rolls, steel balls...

    • Ratiņi tips Siltuma Ārstēšana krāsns

      Ratiņi tips Siltuma Ārstēšana krāsns

      Trolley regenerative heater: Regenerative heating furnace is essentially a combination of efficient regenerative heat exchanger and conventional heating furnace, which is mainly composed of heating furnace body, regenerative chamber, reversing system, fuel, air supply and smoke exhaust system.Regenerator is the main body of waste heat recovery of regenerator flue gas.In a heating furnace, the regenerator is always used in pairs, one stove can use a pair, can use several pairs, even dozens of ...

    • New type heating furnace-heat storage walking heating furnace

      New type heating furnace-heat storage walking h...

      Introduction: The regenerative walking reheating furnace is a new type of reheating furnace, which can greatly reduce energy consumption, and can also improve steel production efficiency and billet quality. Advantage: 1. The supporting beams can be arranged staggered, and the heating quality is better; 2. For square billet and rectangular billet, the billet is heated on all sides, the heating speed is fast, the time in the furnace is short, the oxidation burning loss is small, and the energy ...

    • Double reģeneratīvā apkures krāsns

      Double reģeneratīvā apkures krāsns

      structure: It is composed of heating furnace body, regenerator, reversing system, fuel, air supply and smoke exhaust system. The regenerator is the main body of the flue gas waste heat recovery of the regenerative heating furnace. It is a room-like space filled with the regenerator and is a part of the flue gas and air flow channels. In the heating furnace, the regenerators are always used in pairs. One furnace can use one pair, several pairs, or even dozens of pairs. More than forty pairs ar...

    • Walking bottom heating furnace

      Walking bottom heating furnace

      The walking heating furnace is a continuous heating furnace that moves the billets step by step by the rise, advance, fall, and retreat of the furnace bottom or water-cooled metal beam. The furnace has a fixed bottom and a walking bottom, or a fixed beam and a walking beam. The former is called a walking bottom heating furnace, and the latter is a walking beam heating furnace.

    • Single Stage Gāzes ģenerators

      Single Stage Gāzes ģenerators

      Viena posma gāzes ģeneratoru Viena sadaļas gāzes ģeneratora struktūra vienpakāpes gāzu ģeneratoru vienoto sadaļās struture gāzes plīts Ir daudzas strukturālas formas fiksētā gulta gāzes krāsnīs, kas ir aprakstīti šādi saskaņā ar dažādām daļām: Par fiksēts bed gāze krāsnij ir dažādas strukturālā veidā, saskaņā ar dažādām daļām tika aprakstīts šādi: coal padeves ierīce: intermitējošs ogļu uzlādes pārsegs, double materiāls bell, vibrācijas ogles padevēja, zobu c ...